Most Common Car Issues
Add more parameters
MOST COMMON PROBLEMS
BMW 325/325e 1985
The 1985 BMW 325/325e is a classic 2-door sedan from the renowned 3-Series E30 lineup. Powered by a 2.7L inline-6 engine producing 121 hp, it delivers a balanced mix of performance and efficiency. Manufactured in Dingolfing, Germany, this model epitomizes BMW's engineering excellence of the era.
Spec:
Engine Brake (hp) From
121
Engine Manufacturer
BMW-AG
Engine Number of Cylinders
6
Problems:
Oil leaks
The 1985 BMW 325/325e, especially with a 6-cylinder engine, is prone to oil leaks due to aging gaskets and seals.
Cooling system issues
The cooling system, including the radiator, water pump, and thermostat, often experiences failures that can lead to overheating.
Timing belt failure
The timing belt in this model needs regular replacement; failure to do so can result in severe engine damage.
Fuel injector problems
Fuel injectors can become clogged or fail, leading to poor engine performance or misfires.
Vacuum leaks
Vacuum leaks are common and can cause erratic idle, loss of power, and increased fuel consumption.
Valve cover gasket leaks
The valve cover gasket tends to wear out and leak oil, particularly in older BMW models.
Idle control valve issues
The idle control valve can fail or get dirty, causing rough or unstable idling.
Mass air flow sensor failure
The MAF sensor can fail or become contaminated, leading to incorrect air/fuel mixture and poor engine performance.
Crankshaft position sensor failure
Failure of the crankshaft position sensor can lead to hard starting or no-start conditions.
Exhaust system rust
The exhaust system is prone to rust, particularly in older models, which can lead to leaks and increased noise.
BMW 325/325e 1987
The 1987 BMW 325/325e is a classic 3-Series sedan featuring a 2.7L in-line 6-cylinder engine producing at least 121 horsepower. Manufactured in Dingolfing, Germany, this vehicle runs on gasoline and falls under the Class 1 weight rating. It's equipped with four doors and manual seat belts, making it a quintessential BMW of its era.
Spec:
Engine Brake (hp) From
121
Engine Configuration
In-Line
Engine Manufacturer
BMW-AG
Engine Number of Cylinders
6
Problems:
Oil leaks
Older BMW engines, especially from the 1980s, are known for developing oil leaks from areas like the valve cover gasket, oil pan gasket, and rear main seal.
Cooling system failures
The cooling systems in older BMW models can be prone to failures, including issues with the radiator, water pump, and thermostat, leading to overheating problems.
Vacuum leaks
The rubber hoses and gaskets in the intake system can deteriorate over time, causing vacuum leaks that can lead to rough idling and poor engine performance.
Timing belt or chain issues
Depending on whether this model uses a timing belt or chain, either can wear out or become misaligned over time, which can cause severe engine damage if not addressed.
Fuel injector problems
Fuel injectors can become clogged or fail, leading to poor fuel delivery, misfires, and reduced engine performance.
Ignition system failures
Older BMWs can have issues with ignition components such as the distributor, spark plugs, and ignition coils, which can cause starting problems and misfires.
Head gasket failure
Over time, the head gasket can fail, leading to coolant leaks, oil contamination, and significant engine damage if not repaired.
Worn engine mounts
Engine mounts can wear out, causing excessive engine movement, vibrations, and even damage to other components.
BMW 325/325e 1986
The 1986 BMW 325/325e is a classic sedan from the renowned 3-Series E30 lineup. Powered by a 2.7L in-line 6-cylinder engine, it delivers 121 hp and runs on gasoline. Manufactured in Dingolfing, Germany, this 4-door passenger car features an automatic transmission and manual seat belts. It falls under the Class 1 weight rating, suitable for vehicles 6,000 lb or less.
Spec:
Engine Brake (hp) From
121
Engine Configuration
In-Line
Engine Manufacturer
BMW-AG
Engine Number of Cylinders
6
Problems:
Oil leaks
BMW engines, especially older models like the 1986 325/325e, are known for developing oil leaks from various seals and gaskets, such as the valve cover gasket and oil pan gasket.
Cooling system issues
The cooling system in these engines can be problematic, with common failures including the radiator, water pump, and thermostat, leading to overheating issues.
Timing belt/chain wear
Over time, the timing belt (or chain, depending on the specific engine) can wear out or become loose, which can cause engine performance issues or even catastrophic engine failure if it breaks.
Vacuum leaks
Vacuum hoses and intake boots can become brittle and crack with age, leading to vacuum leaks that can cause rough idling and poor engine performance.
Fuel injector problems
The fuel injectors in older BMW models can become clogged or fail, leading to poor fuel economy, misfires, and reduced engine performance.
Electrical issues
Older BMW models can suffer from various electrical problems, including faulty sensors, wiring issues, and failing engine control units (ECUs), which can affect the overall performance and reliability of the engine.
BMW 325/325e 1985
The 1985 BMW 325/325e is a classic two-door sedan from the 3-Series E30 lineup, featuring a 2.7L inline-six engine producing 121 hp. Manufactured in Dingolfing, Germany, this vehicle runs on gasoline and showcases BMW's engineering excellence.
Spec:
Engine Brake (hp) From
121
Engine Manufacturer
BMW-AG
Engine Number of Cylinders
6
Problems:
Oil leaks
The 1985 BMW 325/325e, especially with a 6-cylinder engine, is prone to oil leaks due to aging gaskets and seals.
Cooling system issues
The cooling system, including the radiator, water pump, and thermostat, often experiences failures that can lead to overheating.
Timing belt failure
The timing belt in this model needs regular replacement; failure to do so can result in severe engine damage.
Fuel injector problems
Fuel injectors can become clogged or fail, leading to poor engine performance or misfires.
Vacuum leaks
Vacuum leaks are common and can cause erratic idle, loss of power, and increased fuel consumption.
Valve cover gasket leaks
The valve cover gasket tends to wear out and leak oil, particularly in older BMW models.
Idle control valve issues
The idle control valve can fail or get dirty, causing rough or unstable idling.
Mass air flow sensor failure
The MAF sensor can fail or become contaminated, leading to incorrect air/fuel mixture and poor engine performance.
Crankshaft position sensor failure
Failure of the crankshaft position sensor can lead to hard starting or no-start conditions.
Exhaust system rust
The exhaust system is prone to rust, particularly in older models, which can lead to leaks and increased noise.
BMW 325/325e 1987
The 1987 BMW 325/325e is a classic sedan from the renowned 3-Series E30 lineup. Under the hood, it features a 2.7L in-line 6-cylinder engine produced by BMW-AG, delivering 121 horsepower. This gasoline-powered vehicle, manufactured in Dingolfing, Germany, offers a blend of performance and vintage charm.
Spec:
Engine Brake (hp) From
121
Engine Configuration
In-Line
Engine Manufacturer
BMW-AG
Engine Number of Cylinders
6
Problems:
Oil leaks
Older BMW engines, especially from the 1980s, are known for developing oil leaks from areas like the valve cover gasket, oil pan gasket, and rear main seal.
Cooling system failures
The cooling systems in older BMW models can be prone to failures, including issues with the radiator, water pump, and thermostat, leading to overheating problems.
Vacuum leaks
The rubber hoses and gaskets in the intake system can deteriorate over time, causing vacuum leaks that can lead to rough idling and poor engine performance.
Timing belt or chain issues
Depending on whether this model uses a timing belt or chain, either can wear out or become misaligned over time, which can cause severe engine damage if not addressed.
Fuel injector problems
Fuel injectors can become clogged or fail, leading to poor fuel delivery, misfires, and reduced engine performance.
Ignition system failures
Older BMWs can have issues with ignition components such as the distributor, spark plugs, and ignition coils, which can cause starting problems and misfires.
Head gasket failure
Over time, the head gasket can fail, leading to coolant leaks, oil contamination, and significant engine damage if not repaired.
Worn engine mounts
Engine mounts can wear out, causing excessive engine movement, vibrations, and even damage to other components.